How to Install a Bathtub ( Guide).
How to Install a Bathtub ( Guide).
Blog Article
The article down below relating to Tools You Need to Install a New Bathtub is particularly entertaining. Check it out yourself and decide what you think of it.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to remove the old tub and position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you might require a specialist plumber to make tube connections.
This article will aid you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub as well as don't need to transform the setup of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited access that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making certain that the washers are in area between the tap as well as the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the tub up until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints and new pipework for leakages and also tighten them if necessary. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub must wait up until the tub has been used at least when as this will certainly resolve it into its final position.
Preparing for the Installment
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealant can break rather very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our piece about Installing A Bathtub. Thanks a lot for taking a few minutes to browse our article. Loved our blog entry? Please share it. Let others find it. I am grateful for your time. Visit us again soon.
Prices & Booking Report this page